what is Steps to clean the pool.at your home

Prepare the cleaning equipment to clean the pool as follows: 1. suction line 2. suction nozzle 3. head hose 4. Convert to the pool. 5. waste scoop Cleaning the pool has this step. 1. Put all debris or leaves inside the pool to the minimum or minimum before sucking. 2. Suck the sludge by following these steps. 2.1 Connect the suction hose to the nozzle and connect the handle to the nozzle. 2.2 Remove the air from the suction line by dipping the nozzle into the water first and then pulling the suction line down until the suction line is full. 2.3 Adjust the length of the handle to fit the size of the pool that will suck the sludge throughout the pool. 2.4 Then suck the sludge from one side of the pool edge and suck in the direction of the tile, alternating with the zipper, which will make the suction as fast and clean as possible. Warning Do not raise the sludge above the water surface in the sucking zone. The air can not be sucked in. Inspection of the machine after sucking sludge. 1. Check the pressure if the pressure of the filter is over 15-20 PSI. The filter or BACK WASH must be cleaned immediately. 2. Check the ducting of the pipe for any residue and if dirty, immediately clean up immediately. 3. Make sure the pump is noisy or abnormal if you have to notify the technician to take care immediately. It will be resolved in time. 4. Check the water pump front basket. If the garbage is clogged, open the lid and remove the waste. Then keep the screws in normal working condition. 5. Check the general condition of water leakage from various wallets? If prompted, inform the pool staff immediately. *** Remarks should be given to skilled technicians. Chemical measurement of the pool 1. PH measurements Clean swimming pool is right The water quality is important. Water in pool when standard It has the following features: - The pH range is between 7.2 - 7.6. - chlorine levels range from 1.0 to 3.0 ppm (part per million) (one chlorine concentrate per 1,000,000 parts water) - Hardness of water between 200 - 400 - Total Alkalinity between 80 - 100 When the water is adjusted to the following conditions, the water will be naturally blue. *** If the pH is lower than 7.2 indicates that the pool water is acidic. Modified by adding a Shada ash. If the pH is greater than 7.6, the water in the pool is alkaline. Cure with acid hydrochloride. If chlorine is less than 1.0, chlorine must be added in the amount calculated. 2. Check the water filter and electrical system in the engine room. 2.1 will need to check the filter pressure. When the pressure exceeds 20 PSI, the filter must be cleaned. ** Filter cleaning procedure. 1. Check the pressure if the pressure of the filter is over 15-20 PSI. The filter or BACK WASH must be cleaned immediately. 2. Check the ducting of the pipe for any residue and if dirty, immediately clean up immediately. 3. Make sure the pump is noisy or abnormal if you have to notify the technician to take care immediately. It will be resolved in time. 4. Check the water pump front basket. If the garbage is clogged, open the lid and remove the waste. Then keep the screws in normal working condition. 5. Check the general condition of water leakage from various wallets? If prompted, inform the pool staff immediately. *** Remarks should be given to skilled technicians. 3. Open-Close Procedure The wah wah system in the normal pool. 3.1 Open the Gulf Surge Tank 3.2 Close the Vacuum Valve 3.3 Close the Main Drain 3.4 open Inlet Valve 3.5. Twist the control cabinet to the Auto. Auto login to work. In case the pool pump can not pull water into the pump. - Vacuum Valve - Inlet Inlet - Turn the Make Up Water (water supply) to fill up the pump. - Main Drain - Twist the control cabinet to Man and open the pump for water. - After the pump can draw water as usual. Keep the water filter system as normal. Sludge pool floor - Vacuum Valve - Shutting Out the Surge Tank - Close the Main Drain. - Inlet Inlet - Twist the front of the charger to Auto and open the pump for sucking. - In the case of suction, do not force the pump to gradually open at one increment (in the case of multiple pools) to be able to absorb more force. 4. Cleaning - Dump the surface of the pool clean. - Scrub around the pool area. - Bring the handle to the suction nozzle. Plug the sludge hose to the nozzle. Bring to soak in the depth of the pool by blowing the wind out of the pipe. When the air out of the line in the pipe and then put the head of the hose to drown into the sucking plug sludge on the edge of the pool. This sludge Sludge water is sucked into the filter to remove sludge. Then filter the dirty water into good water back into the pool again. *** Note must be dismissed air out. Otherwise, the suction force of the pump may be lost. And can not work.